Ignition switches are a common part of electric scooters. Electric scooters are a great way to get around town, but sometimes the ignition switch can become jammed or broken. This can prevent the scooter from starting. In this article, we will show you how to bypass an ignition switch on an electric scooter.
How To Bypass Ignition Switch On Electric Scooter? First, you will need to determine which type of electric scooter you have. Many models have a push button start, while others require you to use the keypad located near the handlebars. If your model requires the keypad, wait until you’re ready to start it before trying to bypass the ignition switch.
If your model has a push button start, press and hold down the start button until the engine starts. Then release the button and ride away.
If your model has a broken or jammed ignition switch, you will need to take it into a repair shop in order to have it replaced. Before doing this, make sure that you understand how to remove and replace an ignition switch on your particular electric scooter.
How Do You Bypass An Ignition Switch?
If you own an electric scooter, there is a good chance that the ignition switch is not working properly. This means that you can’t start the scooter by simply pressing the button.
In order to bypass the ignition switch, you will need to do some research and find a suitable replacement. You can also try using a keyed lock or cable lock to secure the switch. Here is the simple and step by step guide to bypass an ignition switch on your electric scooter.
Remove The Handlebars And Handlebar Tape:
in the very first step you have to remove the handlebar by removing its tape. You could remove the handlebars by removing the screws that hold them in place, or you could remove the handlebar tape by peeling it off.
Loosen The Clutch Cable:
Next you have to loosen the clutch cable. There is a way to bypass the ignition switch on electric scooters to give you temporary power if you need it.
Loosen the clutch cable and hold down the throttle while turning the key to start the scooter. Once you start moving, release the throttle and turn off the key.
Disconnect The Battery:
If it is likely that the ignition switch is stuck in the “run” position then disable the battery. To disable the electric scooter so that it can be safely towed away or repaired, you will need to disconnect the battery.
Remove The Cover Plate:
When your electric scooter is off, the ignition switch may be physically bypassed to allow the engine to run. This is typically done by removing the cover plate on the side of the engine. The cover plate is held in place with two Phillips head screws and can be removed by gently prying it off with a flathead screwdriver.
Once it is removed, use a voltage tester or multimeter to verify that the battery is off before proceeding. If the battery is not off, turn off the power at the main electrical panel and wait five seconds before turning it back on again.
Once you have verified that the battery is off, use a screwdriver to remove one of the two screws that hold in place the cover plate. Next, using your fingers, push up on one end of the cover plate and pull it away from the engine.
Find The Ignition Switch And Unscrew It:
Now locate the ignition switch on your electric scooter. It will likely be located near or under the seat. If your scooter has a handlebar-mounted keypad, be sure to disable it before beginning any repairs.
Some models have switches that must be slid open in order to access the keypad, removing these switches can make starting and stopping your scooter much easier.
Once you’ve located and identified the ignition switch, gently pry it off of its mounting with a small tool such as a screwdriver or knife blade.
Unscrew The Nut That Holds The Switch In Place:
Electric scooters rely on an ignition switch to start the engine. If this switch is disabled, the electric scooter will not start. There are a few ways to bypass an ignition switch on an electric scooter.
One way is to unscrew the nut that holds the switch in place. Once the nut is loose, you can remove the switch and replace it with a new one.
Pull Out The Broken Or Jammed Switch:
If the scooter’s ignition switch is broken or jammed, you’ll need to remove the switch and replace it. Depending on the model of scooter, this may be a simple task involving just a Phillips head screwdriver. In some cases, the switch may just need to be pulled out.
If that’s not possible or doesn’t work, you may have to remove the entire handlebar assembly in order to get at the switch.
Replace the Ignition Switch:
Now replace the ignition switch with a new switch. First of all you have to check the switch that you are already using. When you realize that its time to replace this switch with new one then you may proceed.
Install A New Switch If Necessary:
Replace the cover and screws, then reattach alligator clips to both wires leading from the terminal block and attach them to corresponding terminals on either side of your scooter’s body (behind or under gas tank).
Reconnect all other electrical connections in reverse order, making sure that each connection is made properly before tightening screws. Test your new ignition switch by turning it on in gear and pressing down on its pedal until it clicks into “on” position.
Put It Back In Place:
Finally in order to bypass the ignition and start the scooter, you will need to put it back in place. Properly check all the wires and then tighten the nuts.
What Do You Do If Your Electric Scooter Isn’t Turning On?
If your electric scooter isn’t turning on, there are a few things you can try. First, disconnect all of the wires coming from inside of the scooter, including those coming from the battery and switch. Next, look for screws on either side of the switch that hold it in place (usually there are two).
Remove these screws with a Phillips head screwdriver (or a coin). Once screws are removed, carefully pull out the switch by hand (be careful not to lose any of your cables or wires).
Replace switch with new one and replace screws on each side of scooter. If that still doesn’t work, you might need to take it to a mechanic.
Watch The Video: Bypass Ignition Switch On Electric Scooter:
How Do You Bypass An Ignition Switch Without The Key?
If you need to bypass an ignition switch without the key, there are a few things you can do. First, disconnect all of the wires coming from the switch and battery. Next, unscrew the cover on the switch (usually it has two screws on each side).
Be careful not to lose any of your cables or wires. Once screws are removed, carefully remove the switch by hand (be careful not to lose any of your cables or wires).
Bottom Line: How To Bypass Ignition Switch On Electric Scooter?
In conclusion, if you need to bypass the ignition switch on your electric scooter, it is a relatively easy process. You will need to remove the battery cover, unscrew the battery, and disconnect the wires. Once you have done this, you can screw the battery back in and reattach the battery cover.
FAQs
How Do You Hotwire An Ignition Switch?
If you need to hotwire an ignition switch, there are a few things you need to know. First, unscrew the cover on the switch (usually it has two screws on each side). Secondly, find the black wire going to the battery. Third, find the wire leading from the battery to the switch. Finally, connect these wires together. Be sure that you are connecting them in the correct order!
Where Is Electric Scooter Reset Button?
Electric scooters come with a reset button. This is usually located on the handlebars or near the battery. When you are unable to start your scooter, push this button and wait a few seconds for it to reset.
How Do You Pop An Ignition With A Screwdriver?
If your electric scooter doesn’t start after trying to hotwire the ignition, you may need to pop the switch with a screwdriver. First, find the cover on the switch. It will likely have two screws on each side. Once you’ve unscrewed these, you’ll need to find the black wire going to the battery. You can then find the wire leading from the battery to the switch and connect them together.
What Wires Go To The Ignition Switch?
The wires that go to the ignition switch on an electric scooter are typically black and yellow.
